sliding joint

Numerical simulation on sliding of close joint in rock mass and evaluation on its mechanical behavior

岩体闭合节理摩擦滑动模拟与力学行为研究

Theory solution of the natural frequency of the single tripod sliding universal joint is performed.

对单联三叉杆滑块式万向联轴器的固有频率进行了理论求解。

To overcome the shortcomings of the shear pin type joint and left-hand thread type joint, a sliding sleeve subsurface safety joint is developed.

为了克服剪钉式和反扣式两种安全接头的不足，研制出一种滑套式井下安全接头。

The stress analysis of coupling head of cross head sliding block cardan joint

滑块型万向联轴器叉头应力分析研究

Stress Analysis of a Tripod Sliding Universal Joint with ANSYS Software

利用ANSYS软件对三叉杆滑块式万向联轴器进行应力分析

The Inside Ball Kinematic Simulation Analysis of the Tripod Sliding Universal Joint Based on ADAMS

基于ADAMS的三叉杆滑块式万向联轴器的内球运动仿真分析

An experimental investigation of a mechanism with clearance in tripod-ball sliding joint

含间隙三球销副机构的实验研究

On the basis of the kinematics analysis, complex dynamics analysis is carried out to the single tripod sliding universal joint by the "single force pair" method.

在运动分析的基础上，利用动力学分析中的单个示力副法对单联三叉杆滑块式万向联轴器进行了复杂的动力学分析。

Adaptive Backstepping Sliding Mode Control of Joint Motion in Free Floating Space Manipulator System

空间机械臂关节轨迹跟踪的自适应反演滑模控制

Based on the vectorial frictional impact model introduced in part I, models of revolution clearance joint and sliding ring clearance joint are built up respectively.

基于前一部分建立的矢量形式的含摩擦碰撞模型，分别建立了旋转间隙铰模型和滑环间隙铰模型。

The improved preventing sliding splint over bone joint was used as external fixation.

而外固定采用改良式防滑脱超关节夹板固定。

Sliding sleeve subsurface safety joint for multiple stage usage

可多级使用的滑套式井下安全接头

To ensure the security of this joint, interracial sliding of the joint, tensile failure of the bolts and extruding failure of the interfaces must be prevented.

指出为保证该联接安全可靠，必须满足轴承座底面与游梁接合面间不滑移、螺栓不拉断、接合面不压溃及轴承座不翻转等条件。

Modeling of tripod-ball sliding joint with clearance

新型三球销移动副的间隙模型研究

The Harmonic Response Analysis of the Tripod Sliding Universal Joint

三叉杆滑移式万向联轴器谐响应分析

Dynamic Analysis of the Crank slider Mechanism Including Tripod-ball Sliding Joint with Clearance

含间隙移动副的曲柄滑块机构动力学研究&系统建模和动力学方程

In the procedure the regular destruction features are taken into account, which is tensional crack or shear sliding extending joint interface. The anisotropy of jointed rock masses and plastic deformation induced by rotation of principle stress axes are reflected.

程序中考虑了节理岩体一般均沿节理面受拉开裂或剪切滑移的定向破坏特点，能够反映节理岩体各向异性以及主应力旋转所导致的塑性变形。

Analysis of the Contact Modes of Sliding Joint

移动副的接触型式分析